Nut (fastener): Difference between revisions

From Citizendium
Jump to navigation Jump to search
imported>Howard C. Berkowitz
No edit summary
imported>Howard C. Berkowitz
No edit summary
Line 2: Line 2:
A '''nut''' is an accessory fastening component used with some [[screw (fastener)|screws]] and [[bolt (fastener)|bolts]].  In general, it has an inner hole that is threaded to receive the male threads of the fastener, and an outer hard shell, usually hexagonal or square, that can be turned with a tool called a [[wrench]].  The wrench can be turned either in a direction to tighten or loosen the bond between nut and screw/bolt.
A '''nut''' is an accessory fastening component used with some [[screw (fastener)|screws]] and [[bolt (fastener)|bolts]].  In general, it has an inner hole that is threaded to receive the male threads of the fastener, and an outer hard shell, usually hexagonal or square, that can be turned with a tool called a [[wrench]].  The wrench can be turned either in a direction to tighten or loosen the bond between nut and screw/bolt.


The most common hand wrenches either are open-ended, such that they have sides parallel to two or more facets of the nut, or variously called box or socket, which surround all sides of the nut. A box wrench is a hand tool that can drop over the nut no matter how much of the screw or bolt protrudes, while a socket wrench has a maximum depth of shaft that it can accept. The advantage of sockets is that they can be attached to a wide range of drivers, for mechanical power advantage and sometimes simply to reach the nut through a flexible driveshaft.
Some nuts are intended to be turned by finger pressure. These include ''wing nuts'', which have flanges to provide a grip, or ''cap nuts'', which have knurled or otherwise machined cylindrical heads, which give a neat appearance.
 
Nuts may have additional features to make them more secure. A elastic stop nut has a flexible [[washer (fastener)]] built inside them. A catellated nut has a slot to allow a safety wire or pin to be run through them, blocking motion of the screw or bolt.
 
They are made from a wide range of materials. The metal of a nut should, except in carefully engineered situations, match the metal of the screw or bolt, lest they corrode due to electrolytic effects. Nuts exposed to water need to be rustless, as in stainless steel, galvanized steel, or brass.

Revision as of 14:57, 31 May 2009

This article is a stub and thus not approved.
 Main Article
 Discussion
Related Articles  [?]
Bibliography  [?]
External Links  [?]
Citable Version  [?]
 
https://en.citizendium.org/wiki/index.php?title=Nut_(fastener)&printable=yes
This editable Main Article is under development and subject to a disclaimer.

A nut is an accessory fastening component used with some screws and bolts. In general, it has an inner hole that is threaded to receive the male threads of the fastener, and an outer hard shell, usually hexagonal or square, that can be turned with a tool called a wrench. The wrench can be turned either in a direction to tighten or loosen the bond between nut and screw/bolt.

Some nuts are intended to be turned by finger pressure. These include wing nuts, which have flanges to provide a grip, or cap nuts, which have knurled or otherwise machined cylindrical heads, which give a neat appearance.

Nuts may have additional features to make them more secure. A elastic stop nut has a flexible washer (fastener) built inside them. A catellated nut has a slot to allow a safety wire or pin to be run through them, blocking motion of the screw or bolt.

They are made from a wide range of materials. The metal of a nut should, except in carefully engineered situations, match the metal of the screw or bolt, lest they corrode due to electrolytic effects. Nuts exposed to water need to be rustless, as in stainless steel, galvanized steel, or brass.

Retrieved from "https://citizendium.org/wiki/index.php?title=Nut_(fastener)&oldid=621253"