User:John R. Brews/WP Import

In electronics, the Miller effect accounts for the increase in the equivalent input capacitance of an inverting voltage amplifier due to amplification of the capacitance between the input and output terminals. The additional input capacitance due to the Miller effect is given by

$C_{M}=C(1-A_{v})\ ,$

where A_v is the voltage gain of the amplifier, which is a negative number because it is inverting, and C is the feedback capacitance.

Although the term Miller effect normally refers to capacitance, the amplifier input impedance is modified by the Miller effect by any impedance connected between the input and another node exhibiting gain. These properties of the Miller effect are generalized in Miller's theorem.

History

The Miller effect was named after John Milton Miller. When Miller published his work in 1920, he was working on vacuum tube triodes, however the same theory applies to more modern devices such as bipolar and MOS transistors.

Derivation

(PD) Image: John R. Brews
Miller's theorem

Consider a voltage amplifier of gain −A with an impedance Z_μ connected between its input and output stages. The input signal is provided by a Thévenin voltage source representing the driving stage. The voltage at the input end (node 1) of the coupling impedance is v₁, and at the output end −Av₁. The current through Z_μ according to Ohm's law is given by:

$i_{Z}={\frac {v_{1}-(-A)v_{1}}{Z_{\mu }}}={\frac {v_{1}}{Z_{\mu }/(1+A)}}$.

The input current is:

$i_{1}=i_{Z}+{\frac {v_{1}}{Z_{11}}}\ .$

The impedance of the circuit at node 1 is:

${\frac {1}{Z_{1}}}={\frac {i_{1}}{v_{1}}}={\frac {1+A}{Z_{\mu }}}+{\frac {1}{Z_{11}}}.$

This same input impedance is found if the input stage simply is decoupled from the output stage, and the lower impedance Z_μ / (1+A) is connected in parallel with Z₁₁. Of course, if the input stage is decoupled, no current reaches the output stage. To fix that problem, a dependent current source is attached to the second stage to provide the correct current to the output circuit, as shown in the lower figure. This decoupling scenario is the basis for Miller's theorem and the very noticeable prediction that the input impedance is reduced by the coupling between stages in the amount of the reduced impedance Z_μ / (1+A) shunted across the input is called the Miller effect.

Effects

The Miller effect shows up prominently in amplifier design, where the coupling impedance is a parasitic capacitance. If Z_μ represents a capacitor with impedance Z_μ = 1/jωC_μ, the resulting input impedance has a huge capacitance (1+A)C_μ attached in parallel with the nominal input impedance Z₁₁. This gain-enhanced capacitance is called the Miller capacitance, C_M:

$C_{M}=C_{\mu }(1+A).$

That is, the effective or Miller capacitance C_M is the physical C_μ multiplied by the factor (1+A). This huge capacitance seriously degrades the amplifier frequency performance, because this capacitance becomes a short-circuit at high frequencies, effectively preventing any signal from entering the amplifier. The bigger this Miller capacitance, the lower the frequency at which the amplifier fails to work.

To illustrate this point, suppose Z₁₁ = R₁₁ and Z_Th = R_Th, simple resistors. Application of Kirchhoff's current law at node 1 leads to the result:

${\frac {v_{1}}{v_{Th}}}={\frac {(R_{11}//R_{Th}}{R_{Th})}}\ {\frac {1}{1+j\omega (1+A)C_{\mu }(R_{11}//R_{Th})}}\ ,$

which displays a roll-off of the input signal amplitude v₁ exciting the output stage for frequencies larger than:

$\omega =\omega _{C}={\frac {1}{(1+A)C_{\mu }(R_{11}//R_{Th})}}={\frac {1}{C_{M}(R_{11}//R_{Th})}}\ ,$

where ω_C is called the corner frequency. An interesting point is that this frequency becomes infinite (no roll-off) if the Thévenin resistance R_Th = 0. That is why the parasitic resistance r_X in the base lead of the hybrid-pi model for the bipolar transistor can be influential in determining the amplifier roll-off when these transistors are driven with a very low resistance Thévenin voltage source.

It is also important to note that the Miller capacitance is not the only source of amplifier frequency dependence. It is important to include as well the capacitances contributed by the output stage, and in feedback amplifiers it is this frequency dependence that controls the stability of the amplifier. This frequency dependence can be affected by the dependent current source that the Miller theorem introduces in the output stage.

The Miller effect is not always a nuisance: it may be exploited to synthesize larger capacitors from smaller ones. One such example is in the stabilization of feedback amplifiers, where the required capacitance may be too large to practically include in the circuit. This may be particularly important in the design of integrated circuit, where capacitors can consume significant area, increasing costs.

Miller approximation

This example assumes A is frequency independent, but more generally A is frequency dependent. Because the Miller capacitance depnds upon A, frequency dependence of A makes the Miller capacitance frequency dependent, so it is not possible to interpret C_M as an everyday capacitance independent of frequency. However, in many cases, frequency dependence of A arises only at frequencies higher than the corner frequency caused by the Miller effect, so for frequencies up to the Miller-effect roll-off of the gain does not occur, and A is approximated adequately by its low-frequency value. This approximation, the determination of C_M using A evaluated at low frequencies, is the so-called Miller approximation. So long as the Miller approximation is accurate, C_M is frequency independent, and its interpretation as a capacitance is secure.

Mitigation

The Miller effect may be undesired in many cases, and approaches may be sought to lower its impact. Several such techniques are used in the design of amplifiers. It is important to notice that the frequency limitation due to C_M is greatly reduced for low impedance drivers, that is, C_M R_Th//R₁₁ is small if R_Th is small. Consequently, one way to minimize the Miller effect upon bandwidth is to use a low-impedance driver, for example, by interposing a voltage follower stage between the driver and the amplifier This stage acts as an impedance transformer, reducing the apparent driver impedance seen by the amplifier, reducing the Thévenin resistance of the driver.

A current buffer stage may be added in front of the load to lower the gain A across the coupling impedance Z_μ, though not necessarily the overall gain. For example, a common base amplifier may be used as a current buffer at the output of a common emitter amplifier, forming a cascode amplifier. Inasmuch as the Miller effect is directly a result of this gain, its reduction will decrease the Miller effect and increase the amplifier bandwidth.