Filtration

All unapproved Citizendium articles may contain errors of fact, bias, grammar etc. A version of an article is unapproved unless it is marked as citable with a dedicated green template at the top of the page, as in this version of the 'Biology' article. Citable articles are intended to be of reasonably high quality. The participants in the Citizendium project make no representations about the reliability of Citizendium articles or, generally, their suitability for any purpose. This article is currently being developed as part of an Eduzendium student project in the framework of a course entitled BEE 4640 Bioseparation Processes at Cornell University. The course homepage can be found at CZ:Cornell_University_2010_BEE_4640_Bioseparation_Processes. For the course duration, the article is closed to outside editing. Of course you can always leave comments on the discussion page. The anticipated date of course completion is 21 December 2010. One month after that date at the latest, this notice shall be removed. Besides, many other Citizendium articles welcome your collaboration! Note to course participants: Looking forward to some insightful and useful articles from your collaborations.

This article is about Conventional Filtration, for crossflow filtration see Crossflow filtration.

A large Buchner funnel and small Buchner funnel situated in an air-tight flask attached to a pressure pump.

Filtration is a process by which most or all solid particles in a liquid-solid suspension fluid are separated from the fluid by passing the fluid through a porous medium barrier. In conventional filtration (as opposed to crossflow filtration in which flow is parallel) the incoming fluid, or feed, flows perpendicular to the porous medium. A layer of solids builds up over time on the surface of the medium, while the flux of the feed through the medium approaches a zero asymptote. In bioprocessing, filtration is an early processing step during the recovery phase. Bioprocessing filtration may be employed, for example, to retrieve a target product in solution from an undesired solid mass of freshly ruptured cells. Filtration is particularly valuable in early processing because it allows for an efficient means of volume reduction.

The Processes

Diagram of Conventional filtration (Left) showing feed entering a filter, depositing filter cake on a septum, and leaving the filter as permeate. (Right) Graph of conventional filtration showing building of cake and flux with respect to time.

Filtration deals with the separation of solids in suspension from liquids. A barrier, called the filter medium or septum, catches solid particles that are too large to pass through this medium on an upstream side, while liquids and very fine solid particles pass through the medium to a downstream side. On the septum's upstream surface, the larger solids, caught by the filter medium, form a continuously thickening layer known as a filter cake. As this cake increases in thickness, the flux of material, or flow of filtrate through the filter medium, decreases, approaching a horizontal asymptote at zero. It is therefore necessary to occasionally stop filtration and remove the cake, or systematically clean the filter during filtration, in order to continue a process of filtration for an extended period of time. Several methods and devices have been devised that allow for this filter cleaning while operating, as well as mechanisms permitting easy removal of filtered solids from the filtering machinery.

In mathematical modeling, filter cakes are often treated as non-compressible. Unfortunately, that is not the case in practice. Several factors, including the pressure gradient of the driving force, if applicable, may cause the filter cake to partially collapse. This can make determining the height and resistance of the cake difficult, which in turn renders other variables such as flux and processing time indeterminate.

Design and Operation

The household coffee maker is a commonplace gravity filtration device.

There are four categories of filtration as divided by driving force: gravity, vacuum, pressure and centrifugal force. The last may also be considered a form of centrifugation, and will not be discussed in great detail here. Types of filtration may also be classified by mechanism (sorted by whether solids are stopped at the surface of a cake or trapped within pores of a medium), by objective (sorted by whether a dry solid, clarified liquid, or both are sought), by operating cycle (sorted by whether filtration is continuous or intermittent), or by nature of the solids. For simplification, only classification by driving force, with specific reference to exemplary machinery will be discussed here.

Gravity filtration

The simplest form of filtration uses only the force of gravity to drive a fluid through a porous medium. Since this driving force is relatively weak, the filtrate must be of low viscosity and the slurry generally dilute. The medium is placed orthogonal to the force of gravity and parallel to the ground. An excellent example of such filtration may be found in the common place household drip coffee filter, in which a layer of coffee grounds acts as a pre-established filter cake and the thin paper of the coffee filter is the the filter septum. Liquid coffee streams through the septum into a collecting pot below; coffee grounds remain trapped on the upper side of the septum. Such gravity filters my also be used in industry on a larger scale, for example, the sand gravity filter used in drinking water treatment, however, with only gravity as the driving force, these filters tend to be too slow to meet the demands of most industries.

Vacuum filtration

An example of a rotating drum vacuum filter from US Pat. 2,379,754

A vacuum filter operates by creating a lower pressure on the opposite side of the porous medium with respect to the incoming feed. A vacuum may provide a substantial pressure difference sufficient to filter a filtrate too viscous for a gravity filter to handle. A vacuum filter can also produce a fairly dry solid and provide a means for washing the precipitate. Examples of vacuum filters include the leaf filter, the Buchner funnel, and rotating drum vacuum filters.

Leaf filters are a staple of this design. Essentially, the leaf filters with a low internal pressure (due to vacuum) are immersed in the filtrate mixture until a thick layer of cake has built up on the surface of the leaves. The leaves are then transferred to a washing tank, where wash water is drawn through each leaf until an internal pressure is applied to the leaf, removing the cake. In another example, drums with filter media on the outer face, and an internal vacuum, are partially immersed in and rotated through the filtrate mixture, picking up a layer of solids. As the drum rotates out of the mixture, the precipitate is washed off the surface and collected. Most vacuum filters operate continuously.

Pressure filtration

Several plates and filters from an example of a filter press from US Pat. 2,390,628

If a higher pressure is required than can be achieved via vacuum filtration, such as when an especially viscous liquid is being filtered or filter-aid cannot be used to ease the filtration (see below), a pressure filter may be employed. In pressure filtration, the filtrate is driven through the filter by positive pressure on the feed side of the filter. While there are several forms of pressure filters, the filter press largely dominates the field. Often taking the form of the plate-and-frame filter or the similar plate filter, the filter press is comprised of a series of plates and frames between which the filtering medium is arranged such that the plates tightly stack one against the next, forming small chambers in between. Channels for filtrate or wash and clarified fluid or soiled wash run along the top and bottom of the plate stack. Near the top and bottom of each plate are holes which may alternately be shut to force filtrate or wash entering one hole to flow through the medium to exit an alternate hole on the side of the filter distal to the side from which the filtrate entered. After filtrate has run through the filter press for a time, cake builds up on one side of the filters. The holes may alternately be plugged and wash forced through the device to clean the cake from the filter press device. Pressure filtration has high energy demands and the device cleaning and cake removal process is often sloppy and messy, however, this form of filtration is capable of separating solid-liquid suspensions that other forms of filtration are simply not capable of addressing.

Centrifugal force filtration

Traditional centrifuge devices, such as the basket centrifuge, may be adapted to act as a filter by placing a filter medium orthogonal to the centripetal force. Solids are caught by the medium and may generally be removed by the same arrangement used to remove solids from the traditional centrifuge, such as by stopping the centrifuge or by continuous removal from a rotating element.

Materials

Under Construction

Filter media

Will discuss various materials used as filter medium, when they are used, pros/cons as applicable.

Filter aid

Example Filter Aids

1 paragraph about role of filter aid, what it is and why we use it.

Principles and theory

In most cases of conventional filtration, a solid suspension fluid, or filtrate, flows against a porous medium by application of a pressure gradient across the medium, where the solids in the suspension too large to pass through the medium become trapped on one side of the medium, building up in a layer called a cake, or filter cake. The flow of the liquid filtrate through the porous medium, which is a bed of solids, may be described by Darcy's Law written in the form:

${\frac {1}{A}}{\frac {dV}{dt}}={\frac {\Delta p}{\mu _{o}R}}$

where A is the cross-sectional area of the medium through which the fluid flows, V is the volume of filtrate, t is the time, Δp is the change in pressures across the medium and cake, μ_o is the is the viscosity of the filtrate, and R is the combined (in series) resistance of the filter medium ("R_M") and filter cake ("R_C"), which is:

$R=R_{M}+R_{C}$.

The cake resistance may further be described in terms of the specific cake resistance α the the following form:

$R_{C}=\alpha \rho _{c}\left({\frac {V}{A}}\right)$

where ρ_c is the mass of dry cake solids per unit volume of filtrate.

Darcy's Law for the flow of the liquid filtrate through the bed of solids porous filter medium and cake may therefore be rewritten as:

${\frac {1}{A}}{\frac {dV}{dt}}={\frac {\Delta p}{\mu _{o}\left(\alpha \rho _{c}\left({\frac {V}{A}}\right)+R_{M}\right)}}$

For constant pressure operation, this equation may be integrated with an initial condition of zero filtrate at time zero to yield:

${\frac {t}{\frac {V}{A}}}={\frac {\mu _{o}\alpha \rho _{c}}{2\Delta p}}\left({\frac {V}{A}}\right)+{\frac {\mu _{o}R_{M}}{\Delta p}}$

which may also be rewritten in term of the filtrate density ρ, the ratio of the mass of dry cake solids to the mass of feed c, and the ratio of the mass of wet cake to the mass of dry cake w:

${\frac {t}{\frac {V}{A}}}={\frac {\mu _{o}\alpha \rho c}{2\Delta p\left(1-wc\right)}}\left({\frac {V}{A}}\right)+{\frac {\mu _{o}R_{M}}{\Delta p}}$

Continue or sufficient?

History

Filtration is well established in the arts of science and engineering. In the past century, it does not appear any major significant advances were made, as filtration was essentially already well understood. That is not to say that many refinements and useful smaller innovations were not made, however. A comparison of chemical engineering texts from 1937, 1952, 1997, and 2003, all revealed the same understanding of theory and pointed to the same array of illustrative devices to demonstrate example filters. This strongly suggests little has changed in the art in the previous century.

It appears that it will really take digging into the 1800's to find development information. Uncertain if such depth desired. May need to find very dusty books in basement of Carpenter...

Applications

Under construction. Still looking for specific material.